Thrust & Torque — 7 m EPB (Pressure Term)
Cutterhead thrust and torque estimate for a 7 m epb (pressure term).
Pressurized machines add the face-pressure term: 3 bar across a 7 m face is ~11.5 MN of thrust before a single cutter touches ground. Forgetting this term is the classic under-sized-jacks story in soft-ground bids.
Formula
Note: Planning-level tunnelling estimate — actual TBM performance is set by detailed geotechnical baseline data, machine design and the contractor's means & methods. Use for feasibility framing only.
Cutterhead thrust and torque estimate for a 7 m epb (pressure term). A free tbm performance & tunnelling tool — no sign-up, no upload, instant results in your browser.
About Thrust & Torque — 7 m EPB (Pressure Term)
Thrust & Torque — 7 m EPB (Pressure Term) computes the governing relationship thrust = (n·F + p·A) × (1+friction) · T ≈ α·D³ live as you type. Pressurized machines add the face-pressure term: 3 bar across a 7 m face is ~11.5 MN of thrust before a single cutter touches ground. Forgetting this term is the classic under-sized-jacks story in soft-ground bids. Defaults are pre-filled with realistic values for this exact scenario, and the worked example substitutes your numbers step by step so the math is never a black box.
How to use Thrust & Torque — 7 m EPB (Pressure Term)
- 1Enter your values — Disc cutters, Force per cutter, Diameter, Shield friction & drag share and more (sensible defaults are pre-filled).
- 2Read the live results: Total thrust required, Breakout torque.
- 3Check the "with your numbers" line to see thrust = (n·F + p·A) × (1+friction) · T ≈ α·D³ substituted step by step.
- 4Adjust inputs until the scenario matches yours, then copy or share the result.
Why use Thrust & Torque — 7 m EPB (Pressure Term)?
- ✓Instant, free and private — every calculation runs client-side in your browser; nothing is uploaded
- ✓Built on the stated formula thrust = (n·F + p·A) × (1+friction) · T ≈ α·D³ with authoritative sources cited on the page (Maidl et al., Mechanised Shield Tunnelling, 2nd ed.; Colorado School of Mines TBM performance model)
- ✓Pressurized machines add the face-pressure term: 3 bar across a 7 m face is ~11.5 MN of thrust before a single cutter touches ground.
- ✓Niche-specific defaults give a meaningful worked answer the moment the page loads
Frequently asked questions
What formula does the thrust & torque — 7 m epb (pressure term) use?+
It evaluates thrust = (n·F + p·A) × (1+friction) · T ≈ α·D³, exactly as published. Sources: Maidl et al., Mechanised Shield Tunnelling, 2nd ed.; Colorado School of Mines TBM performance model. The substituted worked example on the page lets you verify every step against the textbook.
How should I read the result — and how far can I trust it?+
Pressurized machines add the face-pressure term: 3 bar across a 7 m face is ~11.5 MN of thrust before a single cutter touches ground. Planning-level tunnelling estimate — actual TBM performance is set by detailed geotechnical baseline data, machine design and the contractor's means & methods. Use for feasibility framing only.
When is this calculator the right tool for the job?+
Cutterhead thrust and torque estimate for a 7 m epb (pressure term). A free tbm performance & tunnelling tool. Forgetting this term is the classic under-sized-jacks story in soft-ground bids. For neighbouring scenarios, the related tools below cover the same engine with different presets.
Do I need to install anything or create an account?+
No. The tool is pure client-side JavaScript: open the page and it works, offline once loaded, with no account, no quota and no data leaving your device.
Related tools
- Thrust & Torque — 10 m Slurry (Pressure Term)
- Thrust & Torque — 8 m Open Gripper TBM
- Thrust & Torque — 9 m Double Shield
- Thrust & Torque — Raise-Bore Reamer (Info)
- Tunnel Logistics — Muck Volume per Metre
- Tunnel Logistics — Muck Car Train Cycle
- Tunnel Logistics — Tunnel Conveyor Capacity
- Shot Weight & Barrel Check — Polystyrene (GPPS)
- Keyway Dimensions Calculator (DIN 6885)
Related Manufacturing tools
Spindle Speed Calculator — Aluminum 6061
Carbide starting RPM for milling Aluminum 6061: n = 1000·Vc/(π·D) with a handbook cutting speed preset.
● LiveSpindle Speed Calculator — Mild Steel 1018
Carbide starting RPM for milling Mild Steel 1018: n = 1000·Vc/(π·D) with a handbook cutting speed preset.
● LiveSpindle Speed Calculator — Stainless 304
Carbide starting RPM for milling Stainless 304: n = 1000·Vc/(π·D) with a handbook cutting speed preset.
● Live